Scale Calibration & Repair in North Houston & IAH, TX
Scale calibration and repair in North Houston, from Greenspoint and Aldine to the cargo roads around Bush Intercontinental (IAH). MNM Scales sends TDA-registered technicians from our Cypress shop to warehouses, freight forwarders, fabrication shops, food distributors and pawn shops across the north side. Every scale leaves with an in-house or NIST-traceable certificate, and repairs are handled on your dock or at our shop.
Freight Country Around the Airport
The north side runs on freight. Cargo buildings and forwarders around IAH bill by weight, cross-dock and distribution warehouses line Beltway 8, the Hardy Toll Road and I-45, and national food brands run plants and cold storage nearby. In between, older industrial pockets off Aldine Bender Road and Airline Drive hold steel, metal and fastener shops, and pawn shops and gold buyers line Airline Drive and Aldine Mail Route.
One recent north-side job shows the mix: a floor scale and a livestock scale kit for a major logistics center near IAH, calibrated and set up in one visit. Freight floors and specialty weighing often share an address up here, so we plan visits to cover everything at once.
North-Side Scales at a Glance
| Industry | What gets weighed | Scales | Class |
|---|---|---|---|
| Air cargo and forwarders | Pallets, crates, parcels | NTEP floor, parcel | III |
| Cross-dock warehouses | Inbound loads | Floor, forklift | III |
| Food plants and distributors | Cases, portions | Washdown bench | III |
| Pawn and gold buyers | Jewelry, bullion | Class II balance | II |
| Steel and fastener shops | Bar, bolts, nuts | Crane, counting | III |
A 48 by 48 inch NTEP floor scale like the Detecto shown above is the workhorse of north-side receiving. Forklift scales such as the Tara MNM Scales system weigh the load on the forks, saving a trip to the floor scale; we install them on your lift and calibrate them on-site. Our loader and forklift scale guide explains how they work.
Scale Problems We Fix Most on the North Side
- Settings changed by accident. A busy dock crew can bump a scale into calibration mode or change its units or filter. We restore the settings and recalibrate across the full range.
- Load cells worn out by forklift traffic. Floor and pallet scales that carry every load eventually lose a cell and start to creep. We test each cell, replace the failed one and recalibrate.
- Cut or crushed cables from pallet jacks and dock plates. We replace or splice the cable and check the scale before we leave.
- Jewelry balances that read unstably near open doors and fans. We relocate, level and calibrate them.
- Counting scales in fastener shops that miscount small parts, usually a sample-size issue we correct on the spot.
Repairs are quoted per job. For peak season or while your scale is in the shop, scale rentals cover every type, from parcel and bench scales to floor, pallet and crane scales.
Freight Charges, Gold and Texas Rules
When a scale sets a freight charge or a buying or selling price, Texas treats it as a commercial weighing device. It must meet NIST Handbook 44 and be suitable for its use, usually an NTEP-approved model, and be placed into service by a registered technician of a TDA-licensed service company, with the RWM-780 report filed and the yearly RWM-700 registration kept current. That covers cargo scales that bill by weight and the balances pawn shops use to buy gold. Our legal-for-trade calibration page lists the steps, and NIST-traceable certificates are available for shippers and auditors who ask for traceability.
High-traffic dock scales should be checked every three to six months; pawn shop balances often follow their inspection schedule. On-site calibration is done during the visit, and drop-off or mail-in scales typically come back in 1 to 3 business days.
Getting to North Houston From Cypress
From FM 529 our technicians head east on SH 6 and FM 1960, then follow Beltway 8 across the north side. Greenspoint is usually about 35 minutes away, and the cargo area at the airport about 45.
| From our Cypress shop to | Main route | Round trip (approx.) |
|---|---|---|
| Greenspoint | SH 6, FM 1960, then Beltway 8 | About 44 miles |
| Aldine (Aldine Bender Rd area) | FM 1960, then Beltway 8 | About 51 miles |
| Bush Intercontinental (IAH) | FM 1960, Beltway 8, then JFK Boulevard | About 61 miles |
A north-side visit costs the $295 on-site call plus $2 per mile, round trip, billed once however many scales we work on, and each scale is then priced by capacity. Our technicians bring their own calibrated test weights for floor and crane scales, so your crew keeps working. Book calibration below, one per scale, and tell us about your dock. More detail: what scale calibration costs.
Book calibration online, priced per scale:
Up to 2.2 kg: Up to 2.2 kg In-House $95 Up to 2.2 kg NIST $395
2.2–6.2 kg: 2.2–6.2 kg In-House $195 2.2–6.2 kg NIST $495
6.2–35 kg: 6.2–35 kg In-House $250 6.2–35 kg NIST $595
35–150 kg: 35–150 kg In-House $350 35–150 kg NIST $750
Over 150 kg: Over 150 kg In-House $495 Over 150 kg NIST $995
Related Services and Nearby Pages
- Industrial scale calibration for floor, pallet and bench scales, scheduled between shifts.
- Scale repair on dock scales, readouts and pallet scale cells.
- Mail-in calibration for a single parcel or bench scale.
- Nearby: Humble and Kingwood, Cypress, The Woodlands and Spring. All scale services.
North Houston Scale Service FAQ
How much does a visit near IAH cost?
The cargo area at Bush Intercontinental is about 61 miles round trip from our shop. The $295 on-site call plus $2 per mile, round trip, is charged once per visit, with each scale priced by capacity.
Can you calibrate our dock scales between shifts?
Yes. Tell us your shift times when you book and we will schedule the visit to keep your docks moving.
Do you install forklift scales?
Yes. We install Tara MNM Scales forklift and loader scales on your lift and calibrate them on-site; each system is also calibrated before it ships.
My pawn shop buys gold by weight. What do I need?
A Class II balance that meets NIST Handbook 44 and is suitable for its use, usually an NTEP-approved model, placed into service by a registered technician of a TDA-licensed service company. We calibrate it and handle the RWM-780 and RWM-700 paperwork.
Do you bring test weights for floor scales?
Yes. Our technicians bring their own certified test weights, including heavy weights for floor and crane scales.
Can you fix a floor scale that a forklift damaged?
Usually. We test each load cell and the cable, replace what failed and recalibrate. Send photos and the model for a quick quote.
Book North Houston Scale Service
Call (832) 290-3120 (24/7) or get a dock-specific quote for your address.